011180/011181 SIP Talk-Back Speaker (Replacement Product Below)

Part Number: 011180

MSRP: $0.00

CyberData's new SIP Talk-Back Speaker enables two-way conversations in settings such as classrooms, offices, medical facilities and clinics. A remote call button (which is included for the SIP-enabled version), enables calls to a predetermined extension that can be initiated from the room with the speaker. The new SIP Talk-Back Speaker also includes a monitor mode function where the speaker may be called from a remote phone that discretely monitors the activity in the room.
  • Push-to-Talk
  • Web-based configuration
  • Web-based firmware upgradeable
  • Plenum-rated enclosure
  • Small footprint
  • High efficiency speaker driver
  • PoE 802.3af-enabled (Powered-over-Ethernet)
  • Network and external speaker volume control
  • Optional external call button and LED indicator
  • Monitor Mode
Protocol SIP RFC 3261 Compatible
Ethernet I/F 10/100 Mbps
Power Input PoE 802.3af
Operating Temperature -10 degrees C to 50 degrees C (14 degrees F to 122 degrees F)
Payload Types G711 A-Law and u-Law + Singlewire HD
Output Level 10 Watts Peak Power
Sensitivity 96dB / 1W / 1M S.P. Level
Dimensions 9" x 2.4"
Warranty 2 Year Limited
Part Number Standard Color 011180, RAL 9002, Gray White
Part Number Optional Color 011181, RAL 9003, Signal White
Are there a set of specs. or standards that define proper spacing for your IP Speakers along a hallway?

In a ceiling mount, you would want about 1 speaker per every 10-15 feet of hallway length. If you used the paging amp you could use 3 paging amps per 100 feet. This assumes average ambient noise and surface attenuation levels.

I am unable to connect with the unit when it is plugged into a Cisco SLM 224P switch.

The cables or switch ports that you are connecting to are set in switch or hub mode instead of endpoint stations. The MDIX setting needs to be changed to MDI since our VoIP products are end stations. From the Cisco SLM 224P User Guide:

Change to MDI: MDI/MDIX displays the Media Dependent Interface (MDI) / Media Dependent Interface with Crossover (MDIX) status on the port. Hubs and switches are deliberately wired the opposite of the way end stations are wired, so that when a hub or switch is connected to an end station, a straight through Ethernet cable can be used, and the pairs are matched up properly. When two hubs or switches are connected to each other, or two end stations are connected to each other, a crossover cable is used to ensure that the correct pairs are connected. The possible field values are: MDIX

Use for hubs and switches. MDI Use for end stations.
I have a Cisco 6513 switch. When I plug in a CyberData VoIP device, the device constantly reboots and will not register to the SIP server.

Please adjust the switch power selection to Power inline static, as opposed to Power inline dynamic. This will allow the device to continuously receive 15.4W of power.

I have a Cisco Catalyst series switch. How do I set the unit so that it can use PoE (under 15.4w) instead of an external power source?

There are known PoE limitations with third party devices on the Cisco Catalyst series switches. This includes the 2500, 3500, and 6500 series switches. It's important to keep in mind that CyberData devices are considered third party devices and require switch port setting adjustments. Be sure to turn power policing off if it has been enabled on your switch. Power policing is disabled by default. Also, configure your port for no shutdown. Use the following command to configure inline power: power inline static max 15400.

What IP phones do you recommend for setting up a Peer to Peer with this device?

Typical Installation 1

Typical Installation 2

Call Button Mounting

Call Button Connection

Auxilliary Analog Speaker

Ceiling Mounting

Mounting Options

Description

CyberData's new SIP Talk-Back Speaker enables two-way conversations in settings such as classrooms, offices, medical facilities and clinics. A remote call button (which is included for the SIP-enabled version), enables calls to a predetermined extension that can be initiated from the room with the speaker. The new SIP Talk-Back Speaker also includes a monitor mode function where the speaker may be called from a remote phone that discretely monitors the activity in the room.

Features

  • Push-to-Talk
  • Web-based configuration
  • Web-based firmware upgradeable
  • Plenum-rated enclosure
  • Small footprint
  • High efficiency speaker driver
  • PoE 802.3af-enabled (Powered-over-Ethernet)
  • Network and external speaker volume control
  • Optional external call button and LED indicator
  • Monitor Mode

Specs

Protocol SIP RFC 3261 Compatible
Ethernet I/F 10/100 Mbps
Power Input PoE 802.3af
Operating Temperature -10 degrees C to 50 degrees C (14 degrees F to 122 degrees F)
Payload Types G711 A-Law and u-Law + Singlewire HD
Output Level 10 Watts Peak Power
Sensitivity 96dB / 1W / 1M S.P. Level
Dimensions 9" x 2.4"
Warranty 2 Year Limited
Part Number Standard Color 011180, RAL 9002, Gray White
Part Number Optional Color 011181, RAL 9003, Signal White

FAQs

Are there a set of specs. or standards that define proper spacing for your IP Speakers along a hallway?

In a ceiling mount, you would want about 1 speaker per every 10-15 feet of hallway length. If you used the paging amp you could use 3 paging amps per 100 feet. This assumes average ambient noise and surface attenuation levels.

I am unable to connect with the unit when it is plugged into a Cisco SLM 224P switch.

The cables or switch ports that you are connecting to are set in switch or hub mode instead of endpoint stations. The MDIX setting needs to be changed to MDI since our VoIP products are end stations. From the Cisco SLM 224P User Guide:

Change to MDI: MDI/MDIX displays the Media Dependent Interface (MDI) / Media Dependent Interface with Crossover (MDIX) status on the port. Hubs and switches are deliberately wired the opposite of the way end stations are wired, so that when a hub or switch is connected to an end station, a straight through Ethernet cable can be used, and the pairs are matched up properly. When two hubs or switches are connected to each other, or two end stations are connected to each other, a crossover cable is used to ensure that the correct pairs are connected. The possible field values are: MDIX

Use for hubs and switches. MDI Use for end stations.
I have a Cisco 6513 switch. When I plug in a CyberData VoIP device, the device constantly reboots and will not register to the SIP server.

Please adjust the switch power selection to Power inline static, as opposed to Power inline dynamic. This will allow the device to continuously receive 15.4W of power.

I have a Cisco Catalyst series switch. How do I set the unit so that it can use PoE (under 15.4w) instead of an external power source?

There are known PoE limitations with third party devices on the Cisco Catalyst series switches. This includes the 2500, 3500, and 6500 series switches. It's important to keep in mind that CyberData devices are considered third party devices and require switch port setting adjustments. Be sure to turn power policing off if it has been enabled on your switch. Power policing is disabled by default. Also, configure your port for no shutdown. Use the following command to configure inline power: power inline static max 15400.

What IP phones do you recommend for setting up a Peer to Peer with this device?

Installation


Typical Installation 1

Typical Installation 2

Call Button Mounting

Call Button Connection

Auxilliary Analog Speaker

Ceiling Mounting

Mounting Options

Downloads