010881 V1 SIP-enabled IP Paging Zone Controller with 4-Port Audio (Replacement Product is 011171)

Part Number: 010881

MSRP: $0.00

The CyberData SIP Zone Controller with Audio-Out is a PoE (Powered over Ethernet 802.3af) and VoIP paging device that enables access to existing paging speakers through a VoIP phone system. The interface is designed to use a standard paging amplifier with audio inputs and supports paging up to 15 zone groups from a VoIP phone.
  • SIP RFC 3261 compatible
  • Dual speed 10/100 Mbps
  • Page up to 15 paging zone groups
  • Web-based configuration
  • Web-based firmware upgradeable
  • PoE 802.3af enabled (Power-over-Ethernet)
  • Connector for external power supply
  • Small footprint
Protocol SIP RFC 3261 Compatible
Ethernet I/F 10/100 Mbps
Power Input PoE 802.3af or 48VDC
Operating Temperature -10 degrees C to 50 degrees C (14 degrees F to 122 degrees F)
Payload Types G711
Output Signal Amplitudes 2.0 VPP maximum
Output Level +2dBm nominal
Total Harmonic Distortion 0.5% maximum
Dimensions 6.11" x 4.05" x 1.15" (L x W x H)
Warranty 2 Year Limited
Part Number 010881
How do I update my firmware?

Check to see if your current firmware is the latest version before attempting to update. Download the latest version firmware which includes the Update Firmware Utility. To upload the firmware from your PC, see your Operations Guide.

What amplifiers has the Zone Controller been tested with for interoperability?

The Zone Controller has been tested with the TOA 900 series power amplifier for interoperability.

After a period of time, my device stops working or is unreachable.

This is a common problem when the re-registration time value is not set correctly. On our device, you need to make sure that the re-registration time value (in minutes) is less than that is set on the IP-PBX server.

On an Asterisk-based VoIP SIP PBX system, the CyberData SIP Device status is "Busy" or ?Unreachable.

In the PBX setup page for the extension of the CyberData device, find the Qualify= value and change it to NO. If the Qualify= value requires a numeric value, then change it to 0. Note that on some Asterisk systems (such as Intuitive Voice) this value is called the Heartbeat= value. Set the Heartbeat= value to NO, and then save the settings. Also, on the product's SIP Setup page, make sure that the Register Expiration (minutes) setting is set to less than 6 minutes (5 minutes is good) because it needs to be a value less than the Asterisk default value of 6 minutes. Save the settings after changing the Register Expiration (minutes) setting.

If I wanted to power the device by using the auxiliary power connector, what type of power supply do I need?

The power connection requires a +48v 380mA (min) power brick. The connector is 2.5mm with a positive center. Cisco's CP-PWR-CUBE-3 power brick is approved.

I am unable to connect with the unit when it is plugged into a Cisco SLM 224P switch.

The cables or switch ports that you are connecting to are set in switch or hub mode instead of endpoint stations. The MDIX setting needs to be changed to MDI since our VoIP products are end stations. From the Cisco SLM 224P User Guide:

Change to MDI: MDI/MDIX displays the Media Dependent Interface (MDI) / Media Dependent Interface with Crossover (MDIX) status on the port. Hubs and switches are deliberately wired the opposite of the way end stations are wired, so that when a hub or switch is connected to an end station, a straight through Ethernet cable can be used, and the pairs are matched up properly. When two hubs or switches are connected to each other, or two end stations are connected to each other, a crossover cable is used to ensure that the correct pairs are connected. The possible field values are: MDIX

Use for hubs and switches. MDI Use for end stations.


Typical Installation

Description

The CyberData SIP Zone Controller with Audio-Out is a PoE (Powered over Ethernet 802.3af) and VoIP paging device that enables access to existing paging speakers through a VoIP phone system. The interface is designed to use a standard paging amplifier with audio inputs and supports paging up to 15 zone groups from a VoIP phone.

Features

  • SIP RFC 3261 compatible
  • Dual speed 10/100 Mbps
  • Page up to 15 paging zone groups
  • Web-based configuration
  • Web-based firmware upgradeable
  • PoE 802.3af enabled (Power-over-Ethernet)
  • Connector for external power supply
  • Small footprint

Specs

Protocol SIP RFC 3261 Compatible
Ethernet I/F 10/100 Mbps
Power Input PoE 802.3af or 48VDC
Operating Temperature -10 degrees C to 50 degrees C (14 degrees F to 122 degrees F)
Payload Types G711
Output Signal Amplitudes 2.0 VPP maximum
Output Level +2dBm nominal
Total Harmonic Distortion 0.5% maximum
Dimensions 6.11" x 4.05" x 1.15" (L x W x H)
Warranty 2 Year Limited
Part Number 010881

FAQs

How do I update my firmware?

Check to see if your current firmware is the latest version before attempting to update. Download the latest version firmware which includes the Update Firmware Utility. To upload the firmware from your PC, see your Operations Guide.

What amplifiers has the Zone Controller been tested with for interoperability?

The Zone Controller has been tested with the TOA 900 series power amplifier for interoperability.

After a period of time, my device stops working or is unreachable.

This is a common problem when the re-registration time value is not set correctly. On our device, you need to make sure that the re-registration time value (in minutes) is less than that is set on the IP-PBX server.

On an Asterisk-based VoIP SIP PBX system, the CyberData SIP Device status is "Busy" or ?Unreachable.

In the PBX setup page for the extension of the CyberData device, find the Qualify= value and change it to NO. If the Qualify= value requires a numeric value, then change it to 0. Note that on some Asterisk systems (such as Intuitive Voice) this value is called the Heartbeat= value. Set the Heartbeat= value to NO, and then save the settings. Also, on the product's SIP Setup page, make sure that the Register Expiration (minutes) setting is set to less than 6 minutes (5 minutes is good) because it needs to be a value less than the Asterisk default value of 6 minutes. Save the settings after changing the Register Expiration (minutes) setting.

If I wanted to power the device by using the auxiliary power connector, what type of power supply do I need?

The power connection requires a +48v 380mA (min) power brick. The connector is 2.5mm with a positive center. Cisco's CP-PWR-CUBE-3 power brick is approved.

I am unable to connect with the unit when it is plugged into a Cisco SLM 224P switch.

The cables or switch ports that you are connecting to are set in switch or hub mode instead of endpoint stations. The MDIX setting needs to be changed to MDI since our VoIP products are end stations. From the Cisco SLM 224P User Guide:

Change to MDI: MDI/MDIX displays the Media Dependent Interface (MDI) / Media Dependent Interface with Crossover (MDIX) status on the port. Hubs and switches are deliberately wired the opposite of the way end stations are wired, so that when a hub or switch is connected to an end station, a straight through Ethernet cable can be used, and the pairs are matched up properly. When two hubs or switches are connected to each other, or two end stations are connected to each other, a crossover cable is used to ensure that the correct pairs are connected. The possible field values are: MDIX

Use for hubs and switches. MDI Use for end stations.

Installation


Typical Installation

Downloads