011105 VoIP Syn-Apps Enabled Speaker – Signal White (RAL 9003)

Part Number: 011105

MSRP: $441.00

The Syn-Apps enabled VoIP V2 IP Speaker is for use with the Syn-Apps SA-Announce notification system. SA-Announce provides text and audio-based paging and mass notification services in real-time or scheduled intervals.
  • SA-Announce compliant
  • Plug-and-Play with SA-Announce for automatic speaker configuration
  • Background / streaming music when combined with Syn-Apps Paging Relay
  • Web-based configuration and firmware upgrades via SA-Announce
  • Plenum-rated enclosure
  • Small footprint
  • High efficiency speaker driver
  • PoE 802.3af-enabled (Powered-over-Ethernet)
  • Network and external speaker volume control
  • Can drive one external analog speaker for greater coverage
Protocol Syn-Apps SA-Announce
Ethernet I/F 10/100 Mbps
Power Input PoE 802.3af
Operating Temperature -10 degrees C to 50 degrees C (14 degrees F to 122 degrees F)
Payload Types G711 A-Law and u-Law
Output Level 10 Watts Peak Power
Sensitivity 96dB / 1W / 1M S.P. Level
Regulatory Compliance FCC Class A, UL 60950
Dimensions 9" x 2.4"
Warranty 2 Year Limited
Part Number Standard Color 011104, RAL 9002, Gray White (replaces 011050)
Part Number Optional Color 011105, RAL 9003, Signal White
Are there a set of specs. or standards that define proper spacing for your IP Speakers along a hallway?

In a ceiling mount, you would want about 1 speaker per every 10-15 feet of hallway length. If you used the paging amp you could use 3 paging amps per 100 feet. This assumes average ambient noise and surface attenuation levels.

I am unable to connect with the unit when it is plugged into a Cisco SLM 224P switch.

The cables or switch ports that you are connecting to are set in switch or hub mode instead of endpoint stations. The MDIX setting needs to be changed to MDI since our VoIP products are end stations. From the Cisco SLM 224P User Guide:

Change to MDI: MDI/MDIX displays the Media Dependent Interface (MDI) / Media Dependent Interface with Crossover (MDIX) status on the port. Hubs and switches are deliberately wired the opposite of the way end stations are wired, so that when a hub or switch is connected to an end station, a straight through Ethernet cable can be used, and the pairs are matched up properly. When two hubs or switches are connected to each other, or two end stations are connected to each other, a crossover cable is used to ensure that the correct pairs are connected. The possible field values are: MDIX

Use for hubs and switches. MDI Use for end stations.

I have a Cisco 6513 switch. When I plug in a CyberData VoIP device, the device constantly reboots and will not register to the SIP server.

Please adjust the switch power selection to Power inline static, as opposed to Power inline dynamic. This will allow the device to continuously receive 15.4W of power.

I have a Cisco Catalyst series switch. How do I set the unit so that it can use PoE (under 15.4w) instead of an external power source?

There are known PoE limitations with third party devices on the Cisco Catalyst series switches. This includes the 2500, 3500, and 6500 series switches. It?s important to keep in mind that CyberData devices are considered third party devices and require switch port setting adjustments. Be sure to turn power policing off if it has been enabled on your switch. Power policing is disabled by default. Also, configure your port for no shutdown. Use the following command to configure inline power: power inline static max 15400


Typical Installation

AC Power

Auxilliary Analog Speaker

Amplifier

Ceiling Mounting

Mounting Bracket
Documentation
Documentation
Description Date
PDF Datasheet DATE:10/28/11
PDF Quick Start Guide DATE:9/25/15
PDF Quick-Reference Placemat DATE:9/25/15
Firmware, Drivers & Utilities
ZIP The SolarWinds TFTP server is used when autoprovisioning firmware updates or audio files.

Description

The Syn-Apps enabled VoIP V2 IP Speaker is for use with the Syn-Apps SA-Announce notification system. SA-Announce provides text and audio-based paging and mass notification services in real-time or scheduled intervals.

Features

  • SA-Announce compliant
  • Plug-and-Play with SA-Announce for automatic speaker configuration
  • Background / streaming music when combined with Syn-Apps Paging Relay
  • Web-based configuration and firmware upgrades via SA-Announce
  • Plenum-rated enclosure
  • Small footprint
  • High efficiency speaker driver
  • PoE 802.3af-enabled (Powered-over-Ethernet)
  • Network and external speaker volume control
  • Can drive one external analog speaker for greater coverage

Specs

Protocol Syn-Apps SA-Announce
Ethernet I/F 10/100 Mbps
Power Input PoE 802.3af
Operating Temperature -10 degrees C to 50 degrees C (14 degrees F to 122 degrees F)
Payload Types G711 A-Law and u-Law
Output Level 10 Watts Peak Power
Sensitivity 96dB / 1W / 1M S.P. Level
Regulatory Compliance FCC Class A, UL 60950
Dimensions 9" x 2.4"
Warranty 2 Year Limited
Part Number Standard Color 011104, RAL 9002, Gray White (replaces 011050)
Part Number Optional Color 011105, RAL 9003, Signal White

FAQs

Are there a set of specs. or standards that define proper spacing for your IP Speakers along a hallway?

In a ceiling mount, you would want about 1 speaker per every 10-15 feet of hallway length. If you used the paging amp you could use 3 paging amps per 100 feet. This assumes average ambient noise and surface attenuation levels.

I am unable to connect with the unit when it is plugged into a Cisco SLM 224P switch.

The cables or switch ports that you are connecting to are set in switch or hub mode instead of endpoint stations. The MDIX setting needs to be changed to MDI since our VoIP products are end stations. From the Cisco SLM 224P User Guide:

Change to MDI: MDI/MDIX displays the Media Dependent Interface (MDI) / Media Dependent Interface with Crossover (MDIX) status on the port. Hubs and switches are deliberately wired the opposite of the way end stations are wired, so that when a hub or switch is connected to an end station, a straight through Ethernet cable can be used, and the pairs are matched up properly. When two hubs or switches are connected to each other, or two end stations are connected to each other, a crossover cable is used to ensure that the correct pairs are connected. The possible field values are: MDIX

Use for hubs and switches. MDI Use for end stations.

I have a Cisco 6513 switch. When I plug in a CyberData VoIP device, the device constantly reboots and will not register to the SIP server.

Please adjust the switch power selection to Power inline static, as opposed to Power inline dynamic. This will allow the device to continuously receive 15.4W of power.

I have a Cisco Catalyst series switch. How do I set the unit so that it can use PoE (under 15.4w) instead of an external power source?

There are known PoE limitations with third party devices on the Cisco Catalyst series switches. This includes the 2500, 3500, and 6500 series switches. It?s important to keep in mind that CyberData devices are considered third party devices and require switch port setting adjustments. Be sure to turn power policing off if it has been enabled on your switch. Power policing is disabled by default. Also, configure your port for no shutdown. Use the following command to configure inline power: power inline static max 15400

Installation


Typical Installation

AC Power

Auxilliary Analog Speaker

Amplifier

Ceiling Mounting

Mounting Bracket

Downloads

Documentation
Documentation
Description Date
PDF Datasheet DATE:10/28/11
PDF Quick Start Guide DATE:9/25/15
PDF Quick-Reference Placemat DATE:9/25/15
Firmware, Drivers & Utilities
ZIP The SolarWinds TFTP server is used when autoprovisioning firmware updates or audio files.